Sterling Silver Crescent and Bead Earrings
MATERIALS Wanted
three" 4 x 1 mm sterling silver rectangle wire
Twenty-one particular 'Λ* head pins
Two turquoise disc beads
Just one Vi* one.7 mm black hollow rubber tube
Two sterling silver ear wires
What guidance would you give you a starting artist?
“Do what you really like. Check out unique media. Provide on a selective, restricted, basis to start with to discover what is effective or what doesn't work for you before you leap into A significant outlay of money and energy.*
-Sally J. Phillips Jewellery Designer
Instruments Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection glasses Hard, flat surface Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Wonderful grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Spherical nose pliers
one.Make use of the ruler to evaluate and mark two one Vi’ parts of four x one mm rectangle sterling silver wire.
2Using a jeweler's observed or tin snips, Slice the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File Each individual end of the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If desired, You should use the file to round the ends from the rectangle wire pieces. Use a fantastic grit sanding pad to go above the realm where you have filed to easy the edges and remove any file marks.
4.Use the ruler to measure and mark /*." from one finish from the 1 Vi’ pieces of rectangle wire and place a mark in the middle of the wire. This is when you can drill the holes to slip The pinnacle pins by.
five.Place on your own basic safety Eyeglasses!!! Spot the 1 Vi" rectangle wire items onto a hard, flat surface. Place The purpose of your awl over the mark that you just designed Vm,' from just one conclusion with the rectangle wire items, and firmly strike after on the highest on the awl using a hammer. This can make a pilot hole for drilling holes into the rectangle wire.
Sterling Silver Crescent and Bead Earrings
Chapter 5
six.Employing a /is" drill little bit. drill holes into one particular stop in the rectangle wire pieces having a handheld rotary tool, flex shaft, or drill push (when however putting on your security glasses!).
7.Utilize the file or great grit sanding pad to do away with any burs or tough edges still left from drilling holes in to the rectangle wire pieces.
eight.Curve both equally 1W items of rectangle wire into a “C" shape using a ring mandrel and rawhide mallet. If you don't have a hoop mandrel and rawhide mallet, use two pair of chain nose pliers. Holding one set of pliers in Just about every hand, grasp Every single stop from the 1 Vi* rectangle wire piece While using the pliers and Carefully bend the rectangle wire into a “C* shape. Compare both of those with the C-shaped rectangle wire pieces and regulate the curves so that they're related in si2e. Set these aside.
nine.Make use of the ruler to measure and mark the rubber tube into 4 equivalent items measuring Vm’ Every. Use scissors to chop the rubber tube.
ten.Spot the turquoise disc bead onto The pinnacle pin and insert a single V·' piece of the rubber tube, put The pinnacle pin throughout the hole during the C-formed rectangle wire, after which add one other V«" bit of rubber tube.
13. Keep The top pin With all the bead, rubber tube, and also the rectangle wire on it in a single hand Together with the wire which you bent pointing toward you. Utilizing the round nose pliers, grip the end of The pinnacle pin wire Men's Rings which is pointing toward you and roll it faraway from you (think about turning the ignition important to get started on your vehicle). Release the pliers from The pinnacle pin wire.
At this time, the opening in the loop at the best of The top pin wire must still be substantial adequate to slip the ear wire on. Once Mens Ring you include the ear wire, utilize the round nose pliers to grasp the loop of the head pin wire and roll it shut. You can utilize the round nose or Men's Rings chain nose pliers to regulate the shape with the loop at the very best Mens Ringmens ring of the head pin if you'll want to.
11. Utilize the ruler to measure and mark /(.’ above the highest piece of the hollow rubber tube. Along with the wire cutters or tin snips, Lower the head pin wire Yu.’ earlier mentioned the top with the hollow rubber tube.
12. Utilize the chain nose pliers to bend The top pin wire next to the highest of the rubber tube in a 90-diploma angle.
14. Repeat these ways for the next earring.